Atlantic Salmon: Choosing the right fly line

Det blir snack om lax, utrustning och mycket annat under Fiskelördag i Umeå.

Swinging flies for salmon is an artform in and of itself, and it’s characterized not only by stubborn tradition but also by semi-religious beliefs and notions. A simple fact, however, is that the right fly line makes a huge difference. No mumbo jumbo or magic – it’s just a plain matter of presenting the fly to the fish at the right distance, depth, angle, and speed.

Tom Roger Bekkeli and Eirik Fjelldal are both super-experienced salmon flyfishermen and having been heavily focused on fly lines and how they influence the way a fly is presented in different conditions and circumstances, they have ended up spending countless hours experimenting and testing. As it turns out, developing fly lines – and more specifically – shooting heads that not only cast well but also reach the right depth and angle to ensure the perfect presentation of your fly, isn’t a simple matter. Far from it

We have sat down to have a word with Eirik and Tom about salmon fishing, about how to choose the right fly line, and about their new Seamless Density fly lines, which have been developed in close cooperation with Scientific Anglers.

Tom Roger Bekkeli and Eirik Fjelldal.

How would you describe the perfect fly line/shooting head for salmon fishing?

Eirik: In my opinion there is not ONE perfect shooting head that can do it all in salmon fishing – and I doubt there will ever be one. Why? Because the effectiveness of a fly line or shooting head will always be a compromise between mass distribution, line profile design, length, technology and density on the one hand and where I fish, under what conditions I fish, and how I want to present the fly on the other hand. These factors are subject to change all the time and therefore there is only one rule: There is no one line to rule them all. This, at least, is how I think about it.

I need different series of lines or different «families of lines». I might want a selection of short lines with different densities to deal with, for example, smaller rivers, deep wading, casting in crammed spots etc. In addition, I might need a selection of longer lines with different densities for bigger rivers, where I have good space and need longer distance.

Now, the reason I use the word «family of lines» is not coincidental. If I want a system of lines where I can use the different densities in a way that actually makes sense – it’s important to get a system of lines and densities from the same manufacturer, same brand and within the same line family. A Sink 5 line from one manufacturer is not necessarily a sink 5 for the next. I want the different steps in densities to make sense and sink the way I want them to and I want the lines to have the same length on the sink section of the line. Only then does having a system of shooting heads make sense. Only then can I actively use for example an Intermediate/sink3 line and change over to an Intermediate/Sink5 line and know for sure that I get the properties I need. For me having a perfect line in salmon fishing, is about having options within a series of lines. Then I will always have One line that is perfect for the actual conditions and scenarios.

What is the most important thing to keep in mind when choosing a fly line for Atlantic salmon fishing?

Eirik: Start by carefully examining where you will be fishing and what type of conditions you’re most likely to encounter. Also do a no-BS assessment on your own casting skills. This is SO important!

I have talked to countless fishing guides throughout the years and usually two things seem to go on repeat. One: Their clients would have caught more fish if their casting skills were better. Two: They would have caught more fish if they were more into proficient fishing lines with heavier densities and they actually had them in their fly fishing tool kit. Often these two things are intertwined and we all know the solution of course. Start casting and training with the kit you will be using before going to your fishing destination. Tune yourself in on the casting, get a feel for how your lines behave, and learn to master all densities. I promise, fly fishing will be way much more fun and you will catch more fish.

Tune yourself in on the casting, get a feel for how your lines behave, and learn to master all densities.

I would go so far to say that what really differentiates really good salmon fishermen from the rest, is their ability to master heavy density lines and know when and how to apply them to the situation at hand. Of course, local knowledge of the river and fish behavior is important. But yet again, your shooting heads is your most important tool when it comes to induce the take. There you have it in a nutshell – free of charge!

I can certainly speak for myself and say that when I started getting all nerdy about my sinking lines and learned how to use them, that’s when I took a giant leap forward as a salmon fisherman and started to hook up with more fish. Significantly more fish!

How can a fly line help induce the take?

Tom: Well, without the right fly line, the angler can’t fish the fly at the right dept with the right speed. One of my favorite things to do is to watch how the salmon react to a fly. If you are lucky enough to be able to spot a salmon in a pool and having your buddy throw a fly at that fish, you can learn a lot. It’s so exciting to see how salmon change behavior when the same fly is presented in different ways.

It’s so exciting to see how salmon change behavior when the same fly is presented in different ways.

I’m 100% convinced that the presentation given by the fly line is much more important than the fly pattern. Seeing how a salmon often changes from not being interested to suddenly shooting out like a rocket to grab the same fly because of, for example, increased fly speed is VERY fascinating. Finding the right combination of speed and depth on a given day is what matters!

What are the most important aspects to take into consideration when designing shooting heads for Atlantic salmon inside the European market?

Eirik: My approach to salmon fishing has always been about being the most effective with the least amount of effort. Salmon fishing can be absolutely brutal – many hours and days on end in crap weather, under crap conditions and no takes. Your fly lines should be the tool that helps you and not an obstacle – something that gets in your way and prevents you from performing. It’s about getting that damn fly out where it needs to be and being able to fish it the way you want it. Without 6 blind casts, lots of swearing, and not being able to land that fly on a straight leader…

So, it’s about designing lines that are relatively easy to cast and angle, with little effort. It’s about designing lines that sink the way they are supposed to: Lines with a tolerance for wind, big and heavy flies etc.

There is a whole specter of things to consider when designing shooting heads. I personally like a shooting head you can just pull straight out of the box and fish with. Stuff that just works. No cutting or gluing on loops and what not. It’s too much of a hassle. I want to spend my time fishing. All features in a shooting head must serve a purpose and add something to it that makes it stand out.

You have been instrumental in developing the new Scientific Anglers UST SD (Seamless Density) lines. Can you tell a little bit about why and how you’ve developed these lines?

Tom: We started planning these lines at the time when we wrapped up the development, testing, and approval process of the UST Short shooting heads in 2015. With the UST Short lines, we had just finished a big series of shorter shooting heads with cutting edge SD technology and of course our heads started spinning on how we could improve the longer heads on the market using the same SD tech.

So, in 2017 Eirik and I packed our bags with all our experience from earlier projects and traveled to the Scientific Anglers’ plant in Midland Michigan. As usual, we teamed up with the R&D wizard, Josh Jenkins, and started cranking out designs and prototypes.

Having the opportunity to travel to the factory and spend several weeks on a project like this is key to success for us. Having Josh and the machines standing by, so we can change and tweak the smallest things from one line to another is priceless. This really allows us to focus on the details to make 100% quality products. Being able to spend time on perfecting everything is pure luxury and it’s thanks to SA that we have this opportunity. For example, spending time on getting rid of an imperfection in the loop like a small wave or hinge is what sets us apart from others. The devil is in the details!

Can you tell a little bit about why the Seamless Density specifically will help connect with more salmon?

Tom: A long sinking tip will fish much deeper than a short sinking tip in the same density. The trouble with lines with very long sinking tips is that they are really hard to design so they cast well. They tend to hinge a lot making them terrible to cast. Also, a drastic change in “mass-per-length” (grams/ft, grains/ft, grams/cm, etc…) will create a hinge. Take the example of going from float to sink 5. This line would create a really bad hinge because the sink 5 material is denser and because it will likely have the same diameter as the floating section it will hinge and wobble when you cast it.

The SD BLEND is a lot better at regulating the transition between densities than traditional 2D or 3D, and we have the ability to extend the transition over a longer part of the line. The density gradually changes over a longer section rather than a drastic density change over a short section (mass-per-length).

Hinging during casting and hinging during sinking are directly related. A line that has a smooth mass transition and no hinging will tend to sink in a straighter line. Again, this is because there are no drastic changes in mass OR density.

A line that has a smooth mass transition and no hinging will tend to sink in a straighter line.

Hinging during the cast will definitely take energy out of the cast and limit how straight the line can land.

The short version is that the SD section works like a “stabilizer” in the line taking away hinging and bouncing that kills the energy in the loop during a cast. This makes sure that all the energy in the loop goes in the right direction, ensuring longer cast and better presentations.

Any tips on how to fish these lines and how to induce the take?

Eirik: I always have 2-3 rods rigged up with different lines – meaning different densities. How I choose to fish a pool depends very much on the character of the pool, the water temperatures, the water levels, and where I expect the fish to be holding etc. Under more normal conditions, I usually first cover the pool with a close-to-the-surface type of line, to see if I can get a fish to rise. Maybe a Float/Intermediate or Intermediate type line. Visual takes will just never go out of fashion! Then I swap rods and go for a heavier line, for example an Intermediate/sink5 to dig the fly down, presenting it closer to where the fish may be lying.

My advice is to try and read the water, taking the conditions and general situation into account, and then come up with a plan. Always have a plan you can work around and apply your shooting heads and flies to from different angles. Also, don’t be afraid to use heavy density lines if the salmon don’t respond to an initial close-to-the-surface presentation of your fly. Try going heavier than you initially thought was necessary. Give the salmon two options – move or take the fly!

My main point is to vary your approach and vary it in a way that really makes a difference. Don’t just change a 5cm fly to an 8cm fly – go from 5cm to 15cm. The same goes for how you use your shooting heads. Don’t just go from an intermediate head to an Intermediate/sink3 – go for an Intermediate/sink7, or why not a 750grain line if you can?! Use all the tools you have in your fly fishing toolbox actively. That’s why shooting heads comes in a range of different densities. If you have one line, you have one tool. If you have 3 lines with different densities, you have 3 tools with different options in your toolbox. Options in salmon fishing aren’t simply nice to have – they’re essential when trying to decode the conditions and hook up with fish.

Fact File – UST SD

  • Powerful taper designed to load modern rods. Turns over heavy flies and long leaders while maintaining a precise delivery of the fly. Handles large fly patterns with excellent turnover
  • Vibrantly colored tracer at the rear end of the head for full control of the swing on distance or in low light conditions
  • The Seamless Density sinking technology provides a super-smooth transition between different densities, eliminating hinging and providing a straight-line connection to the fly
  • Exceptional long sinking tips ensure deep and controlled presentations of the fly
  • Shooting Texture allows the line to be easily lifted from the depth before the next cast

11 different densities and taper profile combinations – A total of 33 shooting heads – Weights ranging from #7-11 – Floating – Sink8

Dela artikeln via e-post

Prenumerera på nyhetsbrevet!


Avslöjande reportage: Svenska trålare uppger fel fångstsiffror

Ungefär hälften av svenska fisketrålare som kontrollerats i Danmark har uppgett fel mängd av den sill och skarpsill som de fångat i Östersjön. De uppgifterna publicerar Sveriges Radios Kaliber. Kalibers granskning visar på ett omfattande problem kring rapporteringen, där de utgått från verksamheten i danska Skagen. Enligt dokument från danska fiskeristyrelsen så är det väldigt

Glädjebeskedet: 100 miljoner kronor till vattenrestaurering

Sportfiskare och andra vattenvänner i Skåne, Blekinge och Kalmar län har anledning att fira denna vecka. Nu satsas det nämligen 100 miljoner (!) kronor på bland annat fiskevård. Det är Länsstyrelsen Skåne som får stöd från EU till att dra igång ett av Europas största vattenrestaureringsprojekt. Drygt 100 miljoner kronor satsas på förbättrad vattenkvalitet och

Tusentals båtmotorer stjäls – branschen har fått nog

Båtbranschen kräver att regeringen tar i med hårdhandskarna kring stölderna av båtmotorer. Runt 1 000 båtmotorer stjäls från sportfiskare och andra svenska båtägare varje månad – och gränsen är nu nådd anser Svenska Båtunionen. De omfattande stölderna av båtmotorer är inte på något sett en ny företeelse, utan flera aktörer har slagit larm om utvecklingen de

Flugfiske: Vilken tafs bör man välja?

Flugfisketafsen är en av utrustningens viktigaste delar och finns att köpa i flera olika utföranden. Men vilken sorts taperad tafs bör man då välja och vilken passar bäst för just ditt fiske? Johan Klingberg ger en kort guide över de vanligaste sorterna på marknaden. Dessvärre är det nästan omöjligt att svara på en sådan fråga

Nu är det klart: Här avgörs SM-finalen i gädda

Boka in datumet 4 oktober 2020 – eller försök åtminstone undvika att arrangera någon gäddfisketävling just då. Nu är det nämligen klart att Stäkets SF fått uppdraget att arrangera SM-finalen i gädda. Det är Sportfiskarnas tävlingskommitté som utsett Stäkets SF som arrangör, och själva tävlingen kommer att avgöras på Mälaren 4 oktober. Tävlingsledare Leif Andersson

Nytt i bokhyllan: Lax & laxfiske

Laxvännen och författaren Jan Johansson har varit en förebild för många sportfiskare, både genom litteraturen och praktiskt utövande. Nu släpper han boken ”Lax & laxfiske – en längtan efter nystigen vildlax”. Jan Johansson från Kungälv har en imponerande meritlista i ryggsäcken när det kommer till både lax- och havsöringsfiske, och i samband med ”International Year

Glädje över slingrande upptäckt i Årefjällen

Åre kommun förknippas mest med öring, röding och harr när det kommer till fiske. Men just nu är det en annan art som står i tillfälligt fokus, efter att den oväntat upptäckts i Ullån – nämligen bäcknejonöga. Många vattendrag kring Åre tätort är hårt påverkade av exploateringen i området, och det pågår massiva insatser för

Båtägare uppmanas sänka hastighet för att skydda ålgräs

Är du båtägare och brukar färdas längs Skånes kust? Då kommer du troligtvis att lägga märka till länsstyrelsens skyltar som riktas till just dig. Länsstyrelsen i Skåne placerar just nu 21 skyltar vid hamnar och andra strategiska platser längs kusten. Målgruppen är bland annat båtburna sportfiskare, och det hela handlar om att skydda det värdefulla

Gigantiska aspen som slog fångstmannen med häpnad

Det finns vissa fångster som färdas över gränserna och tar plats i våra spalter. Den här gigantiska aspen från Nederländerna förtjänar sannerligen att visas upp för omvärlden. Det är nederländske fiskeprofilen Volkmar Strikkers som rapporterar om fisken som han själv knappt trodde fanns – nämligen en asp på 10,7 kilo! När Fiskejournalen kommer i kontakt

Främmande fisken som är på väg norrut i Sverige

Först var det puckellaxen och nu kommer rapporter om att ännu en invasiv art etablerat sig i svenska vatten. Det handlar om svartmunnad smörbult, som nu fångats så långt norrut som Hargshamn vid Upplandskusten. Det är SLU Aqua som rapporterar om fångsten av en svartmunnad smörbult, som kom in till dem 24 augusti genom det



Vilken typ av artikel vill du helst läsa?

Visa resultat

Loading ... Loading ...